Chapter 21 · Water, Slurry Transport, and Dewatering

Slurry properties, dilution and water accounting

A slurry flow has several bases

A process stream with solids mass rate S and water mass rate W has total wet mass rate S + W. For a dispersed slurry at negligible gas content, take component volume as mass divided by density and add phase volumes. For solids components c of mass rate Sᶜ and material density ρᶜ, let Vₛ be their combined particle volume rate. Water volume rate V𝓌 uses density ρ𝓌 on the same mass basis. If densities are in t/m³ and mass rates in t/h, the volumes are in m³/h.

Vₛ = Σc (Sᶜ/ρᶜ).
V𝓌 = W/ρ𝓌.
Q = Vₛ + V𝓌.
ρp = (S + W)/Q.

The effective solids density is S/Vₛ. With dry component fractions gᶜ, the reciprocal is Σc gᶜ/ρᶜ. This harmonic mass-weighting property matters for mixtures of heavy minerals and silicates. A weighted arithmetic mean of the material densities biases the calculated solids volume low. Use real particle density for volume closure and measured bulk density for the volume of a dry bed with voids. A static pile inventory has a different geometric volume than the same grains dispersed in slurry.

The mass fraction w and volume fraction φ of solids answer different questions. Mass fraction transforms to volume fraction with solids density ρₛ and liquid density ρ𝓌. Specific gravity is the ratio of density to a reference water density and has no dimensions.

w = S/(S + W).
φ = (w/ρₛ)/[(w/ρₛ) + (1−w)/ρ𝓌].
ρp = φρₛ + (1−φ)ρ𝓌.

At the same w, heavy minerals occupy less volume than lighter minerals. At the same φ, heavy minerals increase slurry density and the pressure gradient for a fixed head. Class mass on a dry solids basis and density on a slurry basis must refer to the same measured stream. For a slurry of known solids and liquid densities, a bulk density allows inference of φ = (ρp−ρ𝓌)/(ρₛ−ρ𝓌) and w = φρₛ/ρp. Gas and temperature can bias that inference. Changes in mineral composition can shift the relationship between a density meter and solids concentration, even if the meter is well calibrated.

Dilution as a feasible water demand

A solids concentration target w* determines water at unchanged dry-solids flow. For dilution only, the addition is bounded below by zero.

Wtarget = S(1 − w)/w.
Wadd = max(0, Wtarget − W).
Wout = W + Wadd.

This relation is absolute in mass units. The sensitivity to the concentration setting while dilution is required is −S/(w*)². Small changes in a dilute target can therefore make large demands on water supply and downstream hydraulic duty. If the feed is already below target, the branch is infeasible by dilution and the model preserves the feed water. Dewatering or a blend with higher-solids material is necessary to increase concentration. A zero solids fraction target at positive solids has no finite solution.

The active DPSIM Pulp Dilution Control calculates the above demand from its connected process slurry streams, separating connected Water Feed blocks from the process feed. It distributes demand equally across multiple recognized Water Feed connections. It preserves the dry solids and reports water addition. For positive targets, the stream balance assigns the calculated water to the product. Audit the upstream source flow as well as the product, especially if a supply constraint or plant-wide makeup limit is introduced elsewhere in the circuit. The control algebra for a steady target does not resolve a mixing tank's residence time, storage or valve dynamics.

Aeration, rheology and hydraulic loading

The liquid and particle phase volumes give unaerated pulp flow Q. A froth factor F on the hydraulic loading estimates apparent volume Qapp = FQ. It leaves mass rates unchanged. If expansion represents a spatially averaged gas fraction ε with volume-additive gas, then F = 1/(1−ε). This relation can describe an apparent operating point. Actual gas holdup can vary with pressure, residence, mixing and foam collapse. DPSIM's Standard Slurry Pump and Standard Open Launder accept a froth factor for hydraulic calculations. A factor derived for duty estimation should be recorded separately from water recovery, which describes physical liquid transport.

For high solids volume fraction or fine clay content, apparent viscosity can depend strongly on shear. Water-like loss laws and a dilute Stokes settling speed can disagree with pipe or thickener measurements in those regimes. Density determines weight per volume, and viscosity or yield stress determines how momentum is transferred. Both can drive duty. An empirical roughness or viscosity calibration in one pipeline is conditional on the slurry recipe, velocity and concentration range. Independent tests over several solids concentrations help separate rheology effects from an unexplained change in solids mass.

Worked dilution and froth case

A plant stream carries 90 t/h of material at 3.0 t/m³ and 60 t/h of material at 4.5 t/m³. Water is 100 t/h at 1.0 t/m³. Its solids volume rate is 90/3.0 + 60/4.5 = 43.333 m³/h, hence effective solids density is 150/43.333 = 3.46154 t/m³. The unaerated feed volume is 143.333 m³/h and its bulk slurry density is 250/143.333 = 1.74419 t/m³. Solids make up 60.0% of wet mass but 30.23% of pulp volume.

At a 45% mass-solids target, water required is 150(1−0.45)/0.45 = 183.333 t/h. The addition is 83.333 t/h. At unchanged solids population, unaerated volume is 226.667 m³/h, φ is 0.19118 and pulp density is 1.47059 t/m³. If observed froth behavior calls for factor 1.25, its apparent volumetric flow is 283.333 m³/h. Treating the difference as air gives void fraction 0.20 and apparent density 333.333/283.333 = 1.17647 t/m³. Mass flow remains 333.333 t/h, of which exactly 150 t/h is solids. A process model that inserted the apparent extra volume as water would overstate water addition by 56.667 t/h before any recycle errors.

QuantityBefore dilutionAfter dilution
Dry solids (t/h)150.000150.000
Water (t/h)100.000183.333
Unaerated pulp flow (m³/h)143.333226.667
Solids by wet mass60.00%45.00%
Solids by pulp volume30.23%19.12%
Pulp density (t/m³)1.744191.47059

When evaluating alternatives, initially vary the dilution target at fixed solids mass rate and component composition. Report process response, water demand and downstream flow together. For a dry-solids throughput increase, total slurry flow and mass-based concentration targets control volumetric capacity independently of grade. Under a water shortage, replacing plant water with recycled water can satisfy the volumetric demand while changing dissolved species or suspended fines. Treat those as additional balances if they affect metallurgical performance.

Exercises and answers

  1. A slurry is 40% solids by mass, and the solids and liquid densities are 4.0 and 1.0 t/m³. Calculate φ, pulp density, and pulp volume at 140 t/h wet.
  2. The stream in Exercise 1 is targeted to 50% solids by a dilution control. Find the requested water addition and whether the target is met.
  3. A nominal 180 m³/h slurry flows at an apparent 216 m³/h immediately below a flotation launder. Calculate F and implied gas holdup for a volume-additive interpretation.
  4. A pulp assay reports a dry mineral grade of 32%; the wet solids fraction is 45%. How many tonnes per hour of the mineral are carried by 200 t/h wet slurry?

Answers

  1. φ = 0.10/(0.10+0.60) = 0.14286, density is 1.42857 t/m³ and volume is 98 m³/h.
  2. The feed contains 56 t/h solids and 84 t/h water. The target requires 56 t/h water. The requested addition is zero and the outlet remains at 40% solids.
  3. F = 1.20 and ε = 1 − 1/1.20 = 0.1667.
  4. Dry solids mass is 90 t/h, so the mineral rate is 28.8 t/h. This calculation uses a dry-grade fraction on dry solids mass.